Directive 2014/33/EU on the harmonization of the laws of the Member States relating to lifts and safety components for lifts.

Safety rules for the construction and installation of electric lifts (applies to lifts with compliance tested up to 31 August 2017)

Safety rules for the construction and installation of hydraulic lifts (applies to lifts with compliance tested up to August 31, 2017)

Safety rules for the construction and installation of passenger and goods passenger lifts (applies to lifts with compliance tested starting from September 1, 2017)

Safety rules for the construction and installation of new lifts in existing buildings

Safety rules for the construction and installation of electric lifts with inclined path

Safety rules for the construction and installation of Vertical lifting platforms intended for use by persons with impaired mobility

Safety rules for the construction and installation of lifts - Landing doors fire resistance test (the procedure applies to all types of landing doors which are intended to provide a fire barrier to the spread of fire via the lift well)

Safety rules for the construction and installation of lifts, with particular attention to accessibility for persons with disability

Safety rules for the construction and installation of lifts, with particular attention to measures of protection against moderate acts of vandalism

Safety rules for the construction and installation of lifts, with particular attention to measures of protection against serious acts of vandalism

Safety rules for the construction and installation of firefighters lifts (lifts to be used by the firefighters in the event of a fire)

Safety rules for the construction and installation of lifts, with particular attention to the behaviour of lifts in the event of fire

Safety rules for the construction and installation of lifts subject to seismic conditions

Rules for improving the safety of existing passenger lifts and goods lifts

Marking for the "safety components" which are compliant with the safety requirements laid down by the directives or by the applicable EU-regulations.

The Directive lays down the rules aiming at guaranteeing the safety and quality of marine equipment installed on board of the ships flying the flag of EU Member States.

The Certificate of Conformity of the Eurasian Customs Union (EAC)

Fire-rating certification with 120 minutes protection

Fire and heat radiation resistance rating certification with 30 minutes protection

Fire and heat radiation resistance rating certification with 30 minutes protection for glass panels with metal frame

Fire and heat radiation resistance rating certification with 60 minutes protection

Fire-resistance certification (thermal insulation and smoke control) with 60 minutes protection

Fire-resistance certification (thermal insulation and smoke control) with 60 minutes protection, special execution with reduced frame size

Fire-resistance certification (thermal insulation and smoke control) with 60 minutes protection, special execution with reduced frame size

Fire-resistance certification (thermal insulation and smoke control) with 60 minutes protection for glass panels with metal frame

Fire-resistance certification (thermal insulation smoke control) with 120 minutes protection

Fire-resistance certification (thermal insulation and smoke control) with 120 minutes protection, special execution with reduced frame size

Fire-resistance certification (thermal insulation and smoke control) with 120 minutes protection, special execution with reduced frame size

Fire-rating certification for the shipbuilding industry (basic protection)

Fire-rating certification for the shipbuilding industry with 30 minutes protection

Fire-rating certification for the shipbuilding industry with 60 minutes protection

For low and medium-traffic, for standard panels (sliding rollers with 44 mm diameter and truck sliding rails with 40x10 mm thick section)

For medium and high-traffic, for standard panels (sliding rollers with 67 mm diameter and truck sliding rails with 40x10 mm thick section)

For medium and high-traffic, for heavy panels (high mechanical resistance plastic sliding rollers with 67 mm diameter and truck sliding rails with 40x10 mm thick section with stiffeners)

For high-traffic, heavy duty and hi-rise installations, for heavy panels (high mechanical resistance plastic sliding rollers with 90 mm diameter and truck sliding rails with 70x14 mm thick section with stiffeners)

For special applications

Protection against objects with diameter larger than 12 mm

Protection against water or rain drips falling at an angle up to 60° from the vertical line

Protection against dust (no harmful deposits) and spraying water from all directions

Protection against dust (no harmful deposits) and jets of water from all directions

Total protection against dust and against the effects of temporary immersion in water

Protection for use in potentially explosive atmospheres (ATEX Directive)

Protection against objects with diameter larger than 12 mm

This feature allows proper setup of the system (landing door lock and car door operator coupling cam)

The safety contacts have slots in order to achieve a perfect adjustment and correct any misalignments at the end of the assembly

It can be unlocked by means of the special triangular key supplied to the lift engineer in order to free the passengers in the cabin in case of a black-out

Stability of the panels during movement improves

The adjustment systems allows for proper positioning of the panels in regard to the frame and the sliding sill

Standard Aluminium sill profile

They ensure free gliding of the panels while improving noiselessness during the opening and closing cycle of the door

It is an uninterrupted connection steel plate between the landing door sill and the shaft wall below the sill itself. It is a safety component since it prevents entrapment risk in case the cabin should accidentally move with the door open

Product assembly and adjustment manual. Safety information included.

Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from the landing (not for Serie DIAMOND panels)

Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from the landing and from inside the shaft (not for Serie DIAMOND panels)

Panels in special execution designed according to the kind of cladding that the Customer wants to use (not for Serie DIAMOND panels)

Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, only applied to the surfaces which are visible from the landing (not for Serie DIAMOND panels)

Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, only applied to the surfaces which are visible from the landing and from inside the shaft (not for Serie DIAMOND panels)

Frame surfaces treated by electrophoretic deposition or painted with anti-corrosion paint for use in case of saline mist or in saline environment (not for Serie DIAMOND panels)

Panels made of AISI 304 or AISI 316 "food" stainless steel, for use in highly corrosive environments (not for Serie DIAMOND panels)

Panel double-plating towards the inside of the shaft, made of iron plate painted RAL 7038 light orange-peel finish. The panel double-plating can be cladded or finished like the surfaces which are visible from the landing (not for DIAMOND panels)

Panel double-plating towards the inside of the shaft, made of iron plate painted RAL 7038 light orange-peel finish, filled with rockwool. The panel double-plating can be cladded or finished like the surfaces which are visible from the landing (not for DIAMOND panels)

Panels made of iron or stainless steel plate with wider slam edge in order to compensate for size differences with the sill (special sill with extended width)

Panels with safety glass vision panel (100 x H 300 or 100 x H 600 mm), various cladding materials and surface finishings available (stainless steel, plastic-film coated steel, painted, etc. - not for DIAMOND panels)

Panoramic glass-framed panels with laminated safety glass and metal frame, available in various materials and finishings (stainless steel, plastic-film coated steel, painted, etc.)

Panoramic full glass panels (without metal frame) with tempered safety glass with upper and bottom fixings in natural color stainless steel and transparent neutral color methacrylate slam edge profile

Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from the landing

Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from the landing and from inside the shaft

Frame in special execution designed according to the kind of cladding that the Customer wants to use

Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, only applied to the surfaces which are visible from the landing

Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, applied to the surfaces which are visible from the landing and from inside the shaft

Frame surfaces treated by electrophoretic deposition or painted with anti-corrosion paint

Frame made of AISI 304 or AISI 316 "food" stainless steel, for use in highly corrosive environments

Frame double-plating towards the inside of the shaft, painted RAL 7038 light orange-peel finish. Can be cladded or supplied with the same finishing as the frame side visible from the landing

Frame double-plating towards the inside of the shaft, made of iron plate painted RAL 7038 light orange-peel finish, filled with rockwool. Can be cladded or supplied with the same finishing as the frame side visible from the landing

Frame in special execution, with especially reduced place requirements, made of iron or stainless steel tubular or L-shaped profiles, different finishings are available

Special frame with enlarged place requirement in order to cover the side and/or upper spaces beyond the clear opening of the door, it is designed according to the Customer's specifications. The frame size of the fire-rated doors depends on the limits set by the fire-rating certificate

Frame in standard execution with side post "buried" in the floor, mainly used in new installations

Frame in special execution with side post designed for assembly on finished floor, mainly used in modernizations

Special frame with outer edge without fixing holes (side only or side and upper holes). It is an aesthetic solution for all cases where the outer edges of the frame are in sight

Mounting template for the correct positioning of the landing door hanger depending on the sill placement, to be used in case of direct wall fixing (door without frame)

Dowels for wall fixing of the brackets supplied with the goods

Frame setup with C-profiles for a wider depth adjustment range and relevant plumbing of the door

Upon request the hanger can be delivered with full electrical pre-wiring

The lock can be adapted for coupling with car door operators equipped with special coupling cams and different from the PRISMA standard ones

The lock can be adapted for coupling with car door operators equipped with fixed cam

When the re-closing rope is designed to be fitted to the side of the panel or on the outside edge of the landing door hanger it is possible to move the spring inside the panel in order to reduce the overall place requirement of the door

When the re-closing rope is designed be fitted to the side of the panel or on the outside edge of the landing door hanger and it is not possible to move the spring inside the panel (in case of glass panels or panels with insulating materials), in order to reduce the overall place requirement of the door the re-closing spring can be offset over the hanger, horizontally

The door re-closing system with counterweight is available as an-add on as an alternative to the standard spring system. It is recommended for large doors or in case of very heavy panels. It ensures a constant pulling force towards the door closing direction

Set of special brackets which ensure a stiff fixing as well as a wide adjustment range even in case of doors hanging in the shaft or doors without frame (the hanger and the sill are fixed to the wall directly)

They are mainly used in order to stiffen the connection between the panels and the landing door hanger. They are designed for the coupling with panels with special geometry for special applications or modernizations (pre-existing panels)

Useful feature which ensures the proper functioning of the doors at low temperatures outdoors or inside cold stores. A thermostat-measures the temperature and switches the heating system on when the set limit has been reached

According to the reference Standards the door at the lowest floor can be setup and equipped with an additional bistable contact upon request. In this case an additional SET of accessories is installed on the door and a special contact reset key is included in the supply.  

Bistable contact which switches back into position automatically

Bistable contact which switches back into position manually

As a standard, the landing door lock is equipped with an electrical safety contact which confirms the closed status of the door. An additional safety contact can be supplied for position control of the panels sliding truck upon request

As a standard, all hangers are setup for earthing by means of double faston connectors (in and out). Additional earthing screws are available upon request

The kit, which is made up of a device to unlock the door by means of a rope, can be used by lift engineer to open the door at the lowest floor when he/she is in the pit. This add-on is mandatory if the doors are used in lifts compliant with the EN81-20/50 Standards

Steel plate enclosure which almost completely covers the mechanical and moving components of the hanger. Its function is mainly aesthetic, but it also provides partial protection to the hanger itself. Available in various materials and finishings

Triangular key 200 mm long, necessary for the unlocking of the landing door with clear height over 2150 mm and up to 2300 mm

Triangular key 500 mm long, necessary for the unlocking of the landing door with clear height over 2350 mm and up to 2500 mm

Triangular key 1000 mm long, necessary for the unlocking of the landing door with clear height over 2550 mm and up to 3000 mm

Reinforced sill aluminium profile with enlarged cross-section for small loads

Sill profile in Stainless Steel, available in various electro-colored finishings. For passenger lifts

Sill profile made of brass. For passenger lifts

Sill profile made of copper. For passenger lifts

Sill profile for goods lifts with capacity up to 3000 kg, made of tubular iron profiles, painted in black color or in other colors upon request

Sill profile for goods lifts with capacity up to 3000 kg, made of tubular iron profiles, electro-galvanized

Sill profile for goods lifts with capacity up to 3000 kg, made of AISI 304 Stainless Steel tubular profiles

Sill profile for goods lifts with capacity up to 3000 kg, made of AISI 316 Stainless Steel tubular profiles

Sill profile for large goods lifts with capacity over 3000 kg, made of solid-drawn iron profiles, painted black or in other colors upon request

Sill profile for large goods lifts with capacity over 3000 kg, made of solid-drawn iron profiles, electro-galvanized

Sill profile for large goods lifts with capacity over 3000 kg, made of AISI 304 Stainless Steel solid-drawn profiles

Sill profile for large goods lifts with capacity over 3000 kg, made of AISI 316 Stainless Steel solid-drawn profiles

Special sill profile placed below the floor level, in a hidden area. It is an aesthetic solution which ensures an uninterrupted even surface between the landing and cabin floor

It is an element placed between the side posts of the frame and between the sill profile and the landing floor. It is made of the same material and with the same finishing as the sill profile

Useful feature which ensures the proper functioning of the doors at low temperatures outdoors or inside cold stores. A thermostat-measures the temperature and switches the heating system on when the set limit has been reached

Set of special brackets which ensure a stiff fixing as well as a wide adjustment range even in case of doors hanging in the shaft or doors without frame (the hanger and the sill are fixed to the wall directly)

Packing in single cardboard box for each door

Standard packing on pallet with multiple doors. The doors are partially pre-assembled (frame with hanger and sill). The panels are packed separately on a wooden pallet

Standard packing on pallet with multiple doors. The doors are fully pre-assembled

Special packing on pallet with upper and side wooden guards for doors supplied completely unassembled

Special packaging in wooden box with interior lined with bituminous paper

Special packaging compliant with ISPM15 Standards, which lay down phytosanitary measures to prevent the spread of harmful organisms among different continents. The Standards apply to wooden packaging for export to some Extra-European countries

Special customized packaging made on specific request by the Customer

Epoxy powder semi-gloss paint with light orange-peel finish, highly abrasion resistant, suitable for indoors (not for Serie DIAMOND panels)

Very robust and strong hot-dip galvanized fire-painted steel, coated with removable transparent PVC protective film (not for Serie DIAMOND panels)

Semi gloss paint orange-peel finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request (not for Serie DIAMOND panels)

Semi gloss paint smooth finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request (not for Serie DIAMOND panels)

Special paint certified by the RINA notify body intended for use in the shipbuilding industry (not for Serie DIAMOND panels)

Special paint fur use in highly corrosive environments such as chemical and food industry or for outdoors installations in saline environment (not for Serie DIAMOND panels)

AISI 430 Stainless steel version (for indoors) available in Satin or Scotch-Brite surface finishing, used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

AISI 304 Stainless steel version (for both indoors and outdoors) available in Satin or Scotch-Brite surface finishing (some models also available in colored version), used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

AISI 316 Stainless steel version (for outdoors, indoors and for highly corrosive environments) available in Satin or Scotch-Brite surface finishing, used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

AISI 304 Stainless steel version (for both indoors and outdoors) with Patterned surface finishing (various surface patterns as well as different colors are available for some models) , used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

AISI 316 Stainless steel version (for outdoors, indoors and for highly corrosive environments) with Patterned surface finishing (various surface patterns are available), used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for DIAMOND panels)

AISI 304 Stainless steel version (for the chemical and food industry, for outdoors, indoors and for corrosive environments) available in various surface finishings, used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

AISI 316 Stainless steel version (for the chemical and food industry, for outdoors, indoors and for highly corrosive environments) available in various surface finishings, used as cladding material to be applied over the structural elements of the panels and frames or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)

Galvanized iron plate coated in plastic film available in various surface finishing, used as cladding material to be applied over the structural elements of panels and frames or directly for self-bearing construction of such elements (not for DIAMOND panels)

Brass sheets are used as cladding for the panels and frames structural elements. It is available with polished or satin finish, rough or with anti-oxidation surface treatment (not for Serie DIAMOND panels)

Copper steel plate is used as cladding for the panels and frames structural elements. It is available with semi-polished or satin finish, rough or with anti-oxidation surface treatment (not for Serie DIAMOND panels)

Corten Weathering Steel (CORrosion resistance + TENsile strength) is a material which exhibits very high self-protection capacity against electrochemical corrosion. It is used as cladding for the panels and frames structural elements and it can be supplied rough or with transparent paint coating or waxed (not for DIAMOND panels)

Raw iron is often used as a finishing element in industrial design. For doors it is used as cladding for the panels and frames structural elements and it can be supplied with rough blackened or pickled surface finishing, with or without transparent anti-corrosion surface coating (not for DIAMOND panels)

The laminated plastic steel plate is only used for cladding of the panels. The material is available as flat sheet and requires holding profiles on the panel side edges. The laminated plastic steel plate is available in various patterns and colors and the holding profiles are also available in various materials and finishings (not for DIAMOND panels)

Highly protective coating which provides very high corrosions resistance

Semi gloss paint smooth finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request

The main components (baseplate, sliding trucks, sliding guides, etc.) are made of AISI 304 Stainless Steel (for chemical and food industry, for outside installations, for interiors as well as corrosive environments)

The main components (groundplate, sliding trucks, sliding guides, etc.) are made of AISI 316 Stainless Steel (for chemical and food industry, for outside installations, for interiors as well as especially corrosive environments)